Condition | New |
---|---|
CNC or Not | CNC |
Model Number | Guangming 0.18 2000 meters tax excluded |
Origin | Mainland China |
Certification | NONE |
Item Description | Molybdenum Wire |
Type | High - speed |
Diameter | 0.16mm, 0.18mm, 0.20mm |
Length | 2000m, 3000m |
Application | WEDM Wire Cutting |
Weight | 500g |
High Speed 0.16mm 0.18mm 0.20mm Molybdenum Wire For WEDM Wire Cutting Mahine High Efficiency 2000m Wire-cut Molybdenum Wire
129.99 $
75961 in stock
High Speed 0.16mm 0.18mm 0.20mm Molybdenum Wire For WEDM Wire Cutting Mahine High Efficientcy 2000m Wire-cut Molybdenum Wire
Features:
1. This molybdenum product has super strength of extension.
2. It features excellent oxidation and corrosion resistance in a variety of harsh thermal and corrosive environments.
3. Molybdenum wire is stable and high precision in cutting. It is not easy to fracture and has long operating life.
4. The molybdenum product is in vacuum package and accurate in measuring. It can preserve for a long time.
5. Its melting point is 2620°C 4748 °F, featuring good electrical and thermal conductivity.
Applications:
1. Circles the filament core, the support wire, the lead-out wire, the electronics grid and so on.
2. The support silk, the lead-out wire guide rod, the electricity vacuum components, the heater element, the high temp electric resistance furnace gives off heat the material and so on.
3. For EMD wire cut, high tensile strength, small elongation ratio, good stability, high cutting precision.
Parameters:
Dinameter: 0.15mm, 0.16mm, 0.18mm, 0.20mm
Wire length: 2000m, 3000m
Purity: >99.99
Material: Molybdenum /Mo
Broken wires related to molybdenum wires
1. Tension and threading speed
1 Increasing the tension of molybdenum wire can reduce the impact of wire vibration, thus improving the precision and cutting speed, and significantly reducing wire breakage. Generally, it is considered that the tension is 12-15N.
2 The increase of wire speed is beneficial to the molybdenum wire to bring the working fluid into the discharge gap of the workpiece with larger thickness, ensuring the elimination of the corrosion products and the stability of the EDM. However, if the wire speed is too high and the molybdenum wire shakes seriously, the stability of processing will be damaged, the processing accuracy and surface roughness will become worse, and wire breakage will be easily caused. When the wire speed is too low, the wire is easy to break due to large loss, so it is better to be less than 10m/s in general experience.
Broken wire related to guide wire structure
1. Broken wires related to the thread carrier
1 The different axes of the inner and outer circles of the thread carrier will produce unbalanced inertia, which will easily lead to wire breakage due to wire stacking during operation.
2 The shaft, bearing and other parts of the silk conveying cylinder often have clearance due to wear, which is easy to cause wire jitter and wire breakage.
3 If the high-frequency power supply is not cut off during the reversing of the screw barrel, the molybdenum wire will burn in a short time due to high temperature. Therefore, it is necessary to check whether the travel switch at the rear end of the screw barrel fails whether the relay controlling the high-frequency is damaged.
4 Keep the thread carrier and guide wheel rotating flexibly, otherwise the vibration of the wire guide system will cause wire breakage during the round-trip operation.
5 It is necessary to adjust the limit stop at the rear end of the thread carrier to prevent the thread from breaking due to the limit stroke of the thread carrier.
6 The machine shall be stopped shortly after the change to prevent the drive parts from being damaged and molybdenum wires from being pulled off by the wire conveying cylinder due to inertia overtravel.
2. Broken wire related to guide wheel and conductive block
1 If the guide wheel and conductive block have grooves due to wear, or the guide wheel bearing has gaps due to wear, it is easy to cause molybdenum wire jitter and wire breakage.
2 It should be ensured that the molybdenum wire and the conductive block, the processing workpiece and the worktable are in good contact, otherwise the high-frequency power cathode can not be connected with the molybdenum wire or cause poor contact.
Wire breakage during machining thick workpieces
Molybdenum coil
Thick workpieces generally refer to workpieces with thickness greater than 100mm. The main reasons for wire breakage are:
1. Broken wire at the beginning of cutting
This is because the molybdenum wire is outside the workpiece during initial cutting, and the distance between the upper and lower guide wheels is large, which causes the molybdenum wire to pull and shake, making the gap between the molybdenum wire and the workpiece unstable, which is easy to form arc discharge, so that the arc is concentrated in a certain section, which will cause wire breakage. In EDM, arc discharge is the main factor that causes the cathode corrosion damage.
2. Wire breakage during cutting
When the molybdenum wire cuts into the workpiece, due to the narrow kerf and the difficulty of emulsion penetration, it is not easy to remove the electric erosion carbon black and metal in the kerf, which worsens the processing conditions. Secondary and tertiary electric discharge machining is generated in the kerf, which causes the kerf to become wider and the gap to enter into a poor state, causing the pulse to form an arc discharge, causing wire breakage.
3. Broken wire at the end of cutting
In addition to the above reasons, the wire breakage after fast cutting is still several millimeters or even tens of microns away, and the wire breakage caused by the deformation caused by the dead weight of the workpiece or the internal stress of the workpiece material, the solution is: simple jigs and fixtures can be self-made, and the material factory can make necessary heat treatment before processing.
Wire breakage related to working fluid
1. When the working fluid turns black, its comprehensive performance will become worse, which is very easy to cause wire breakage. Therefore, it is necessary to observe its color and smell its smell frequently, and replace it in time in case of any abnormality, so as to maintain a certain dielectric capacity of the working fluid. In particular, when machining hard alloy, there are many erosions, which easily lead to poor permeability and fluidity of the working fluid, resulting in poor chip removal.
2. How to identify saponification solution
1 Wrap a little new molybdenum wire and try to cut it on the workpiece for about 1 hour. Observe the color of the molybdenum wire. If the molybdenum wire is gray white, the coolant can cut thinner workpieces, such as gray white mixed with black spots or black stripes. The diameter of the black stripes becomes significantly thinner, so it is necessary to replace the working fluid.
2 Look at arcing and path current. Start the wire carrier, manually force the high-frequency current to connect, and make the molybdenum wire slowly close to the workpiece. Do not touch the workpiece. The spacing is about 1-1.5mm. At this time, there should be no sparks. Then cool the workpiece to make the distance between molybdenum wire and workpiece form a liquid path. If there is a spark or the reading value of the ammeter is increased by more than 10mA on the basis of the original no-load about 30mA for no-load, the working fluid can no longer be used at this time.
Broken wires related to electrical parameters
1. Select reasonable electrical parameters according to the thickness of the workpiece, and open the pulse interval to facilitate the discharge of molten metal particles. At the same time, the no-load voltage of the peak current should not be too high, otherwise, the single pulse energy will become larger, the cutting speed will be accelerated, and it is easy to produce concentrated discharge and arc, causing wire breakage. Generally, the no-load voltage is about 100V.
2. Select the appropriate discharge gap according to the thickness of the workpiece. If the discharge gap is too small, it is easy to cause short circuit, and it is not conducive to cooling and removal of electric erosion; Excessive discharge gap will affect surface roughness and machining speed. When cutting workpieces with large thickness, large pulse width current should be selected as far as possible, and discharge gap should also be correspondingly larger generally greater than 0.02mm to enhance chip removal effect and improve cutting stability
Broken wires related to high-frequency power supply
1. If the peak value of short circuit current is too large, that is, the number of power amplifier tubes input is too large, which exceeds the current that the molybdenum wire can withstand, the molybdenum wire will overheat and brittle fracture due to excessive fatigue.
2. If the negative wave of high-frequency pulse is too large, the negative wave of the pulse will directly corrode the molybdenum wire, increasing the wire loss, reducing the service life of the wire, and causing wire breakage in a short time.
3. If the pulse width and pulse interval are not properly selected, when machining the workpiece with large thickness, the pulse width is too large, which will cause the discharge point concentration in the discharge gap and burn the molybdenum wire; If the pulse interval is too small, the erosion in the gap cannot be fully discharged, the deionization is not sufficient, and the wire is easy to break. At this time, burn marks i.e. black spots can be clearly seen on the molybdenum wire.
Broken wires related to table movement
1. The cutting accuracy of the workpiece is guaranteed by the screw rod, and the clearance between the screw rod and the nut is eliminated by the spring. If the screw rod is poorly lubricated or the spring force is insufficient, the worktable will move at an uneven speed. In this case, the high-frequency current will cause frequent short circuits. If the fault is not eliminated in time, the wire will be broken.
2. When adjusting the frequency conversion tracking speed, try to make the feed speed approximately equal to the working etching speed, so that the pulse utilization rate is high, the processing speed is fast, and the processing state is stable. The feed speed is too high, the short circuit is frequent, and the wire aging is fast. It can be seen from the ammeter that the processing current is large; If the processing speed is too low and the feed speed is too slow, it is easy to make the discharge gap unstable, generate transient arc discharge, and easily burn the molybdenum wire.
Więcej podobnych produktów od innych sprzedawców
-
Sale!
Victor TKF Offensive Badminton Racket Full Carbon G5 Ultralight Professional Badminton Racket 24-32 LBS Racquet Sports Training
169.60 $ -
Sale!
VZ Full Carbon Fiber Strung Badminton Rackets 10U 54.5G Tension Max 30LBS 13kg Training Racquet Speed Sports With Gift Box For
Details parameter: Weight - 10U Net weight only 54.5g without the linewith line<80g& overgrip & plastic film,anyone can control the racket effortless ; CARBON FIBER - he racket more lighter but stronger , so the tension can up to 30LBS,suitable the begining and the profesional player ; BALANCE OF THE RACKET - Racket have the best balance of weight&power,so the racket can easly to break out the power and make the offensive can`t be stop. FREE SERVICE - We can offer the free service of string27lb,so you can play immediately when you get the racket. [...]
99.59 $ -
Sale!
Ultra Light 8U 62g Carbon Fiber Badminton Rackets Professional Offensive Type Racket With Strings Bags G5 Padel Sports
82.29 $ -
Sale!
Original Mikasa Volleyball V300W FIVB Official Game Ball FIVB Approved for Competition Adult Ball Volleyball
Feature: FIVB Approved, professional ball sports brand, designated ball for the 2008 Olympic Games; With 8 panels design, the model looks good; Wear-resistant and soft PU material; Double-layer composite concave material on the surface; Comfortable and soft feel, low impact force; Flight is more stable and easier to control; Brand: Mikasa Model: V300W Circumference: 65-68 mm Weight: 260--280 g Material: Double-layer composite concave material on the surface Process: Splicing and Pasting Applies to: School Competition, Amateur Competition, International Volleyball [...]
189.50 $ -
Sale!
Yonex badminton racket single shot beginner entry carbon one feather racket NR7000i blue has been threaded
101.66 $ -
Sale!
L69A Lathe Tool Holder Quick Change Set for Lathe Metal Post C2/3 SC/2 Professional Turning Tool WM210V/WM180V/0618 Industr
Lathe Tool Holder Quick Change Set for Lathe Metal Post C2/3 SC/2 Professional Turning Tool IndustrOOTDTY Features: 100 brand new and high quality.Insures smoother turning without chatter or vibration.Made with advanced technology, high quality stainless steel, sturdy and durable.It is easy to install and to use.Quick change tool post sets advanced design provides built-in quick tool changing versatility with positive rigidity to meet the most exacting working tolerances.The package includes 1x basic body, 3x steel holder AaD 1250, 1x steel holder AaH 1250, 1x wrench and 1x square key.The use of multiple toolholders form an artificial tool magazine, [...]
266.71 $ -
CNC Electric Hydraulic Press Brake Metal Plate Bending Machine Stainless Steel Folding Tools Servo Dual DA52S System Sale
CNC Electric Hydraulic Press Brake Metal Plate Bending Machine Stainless Steel Folding Tools Servo Dual DA52S System Sale product description Press brake is a kind of machine specially in bending plate, mainly used in automotive manufacturing, kitchen appliance manufac turing, electricity poles, lamp posts,ship-building, military industry, steel industry, mechanical manufacturing. Bending dies can be designed and changed according to customers' different needs.Main types of press brake produced by our company are: manual torsion, CNC torsion press brake, electro-hydraulic press brake, large electro-hydraulic synchronization press brake Currently, production for many years, and stable performance. CNC Electric Hydraulic Press Brake Metal [...]
45,722.04 $ -
Sale!
SHIMOYAMA Plastic Bag Clips Food Sealed Sticks Kitchen Food Snack Grip Organizer Bag Seal Clip Rod Moisture-Proof Storage Clamp
★Brand: 霜山 SHIMOYAMA ★Product name: Plastic Food Bag Sealer Sealing Clip Rod ★Function: Food Storage Snack Clip ★Material: Plastic, PP ★Usage: Food Fresh ★Color: Red Black ★Packing: 6pcs/set ★ 6/12/24pcs x Food Storage Snack Clip ★1.Please allow 1-3MM differs due to manual measurement. ★2.Due to different producing batches, product details might be a [...]
45.15 $ -
3X 1/4 Inch Impact Drive Hex Shank Quick Release Change Holder Bit Drill Chuck Adapter
body { font-size: 75; color: #000; font-family: Open line-height: 1.3; } dl { margin: 0px; width: 480px; float: left; } dt { width: 100px; height: 15px; float: left; } dd { width: 240px; height: 15px; float: left; } dl dt { margin: 0px; line-height: 22px; color: #474747; font-size: 14px; font-family: tahoma; } #product-desc { width: 100; height: 209px; } #description { width: 100; height: 50; [...]
56.03 $ -
Sale!
Water Ring Game Toykids Games Handheld Tosschild Retro Fun Mini Playthings Fight Waterful Target Lasso Pastime Basketball Party
45.23 $ -
Sale!
VEVOR 1020 Cylindrical Laser Engraver 15W GRBL Control Cnc Router 15-100mm Dia Cans Wood Laser Engraving Mini Milling Machine
Product Description 15W Cylindrical Engraver Machine This laser engraving machine is specially designed for cylindrical objects with an active working area of 100x200mm. It features a USB port and GRBL control board, able to be controlled easily with computers. The mini laser engraver can be used to engrave all types of stainless steel, cans, wood, paper tube plastic with a diameter of 15mm-100mm, which is an excellent affordable self-learning engraving tool! Adjustable Lens GRBL Control Board Portable Size Widely Applied Tough Equipment & Tools, Pay Less VEVOR is a leading brand that specializes in equipment and tools. Along with thousands [...]
705.79 $ -
Sale!
ORTUR Lazer Master 2 Laser Engraving Cutting Machine Woodwork Tool Business Machine Air Assist Laser CNC Router Laser Engraver
ORTUR Lazer Master 2 Laser Engraving Cutting Machine Woodwork Tool Business Machine Air Assist Laser CNC Router Laser Engraver Welcome to Ortur Official Store, please note: a. Freeshipping is not means free duty. As we all known, import high value goods would be charged import tax in each country; AND NOT included the remote area charge too b. Seller's shipping methods are shipping by express company, such as DHL/FedEx/ UPS/ TNT; c. Tax Breaks to EU MEMBER countries(Shipment From China Warehouse, please contact our customer service, but need 20-40 days to delivery. d. Fast delivery from overseas warehouse [...]
327.25 $
Reviews
There are no reviews yet.